Home Router & ONT Setup Guides

How to Connect

Connect the blue Internet (WAN) port to your fiber ONT or CPE. Connect your PC via Ethernet to any yellow LAN port (1-4) or connect via the default Wi-Fi credentials on the bottom sticker.

Numbered Setup Steps

1. 1Open browser and visit http://192.168.0.1 (or http://tplinkwifi.net).
2. 2Create a new administrator password when prompted.
3. 3In Quick Setup, select your Time Zone and Internet Connection Type (PPPoE or Dynamic IP).
4. 4Configure your 2.4 GHz and 5 GHz wireless network SSIDs and passwords.
5. 5If used behind another gateway, switch Operation Mode from 'Wireless Router' to 'Access Point'.
6. 6Save and apply settings. Confirm Internet status shows active.

Verification Step

How to Connect

Connect the SC/APC fiber patch cord to the PON port. Connect PC to LAN1 using an Ethernet cable. Set PC to Obtain IP automatically (192.168.100.x subnet).

Numbered Setup Steps

1. 1Open web browser to http://192.168.100.1.
2. 2Sign in with 'telecomadmin' / 'admintelecom' (or check carrier credentials).
3. 3Navigate to WAN > WAN Configuration. Click 'New' to create WAN profile.
4. 4Set Mode to 'Route' (or 'Bridge') and Service List to 'INTERNET'.
5. 5Enable VLAN tagging if required by your OLT and enter ISP VLAN ID.
6. 6Set WAN IP Mode to PPPoE or DHCP. Configure customer Wi-Fi under WLAN.

Verification Step

How to Connect

Insert green SC/APC optical connector into optical port. Connect PC to LAN1. Ensure PON LED turns solid green when registered with the OLT.

Numbered Setup Steps

1. 1Open http://192.168.100.1 in your browser.
2. 2Authenticate using carrier credentials or details printed on the bottom label.
3. 3In WAN configuration, create or edit the Internet profile with proper VLAN tag.
4. 4Bind LAN ports 1 through 4 to the WAN interface.
5. 5Under WLAN settings, configure Wi-Fi 6 (802.11ax) parameters and WPA3 security.
6. 6Verify DHCP Server scope and DNS servers. Click Apply.

Verification Step

How to Connect

Connect the SC/APC fiber drop to the PON port. Connect PC via Ethernet cable to LAN1. Set PC to Obtain an IP address automatically (192.168.1.x).

Numbered Setup Steps

1. 1Visit http://192.168.1.1 in browser.
2. 2Log in with 'admin' / 'admin' (or carrier credentials like 'user' / 'user').
3. 3Navigate to Network > WAN > WAN Connection.
4. 4Create or edit connection: Mode 'Route' or 'Bridge', Link Type 'IP' or 'PPP'.
5. 5Enter ISP VLAN ID and 802.1p priority tag if mandated by your network.
6. 6Navigate to Network > WLAN > SSID Settings to configure Wi-Fi security keys. Click Save.

Verification Step

How to Connect

Connect the yellow WAN port to your incoming fiber ONT or CPE. Connect PC to any LAN port (1-3) or connect to the default Reyee Wi-Fi.

Numbered Setup Steps

1. 1Open browser to http://192.168.110.1 (or use the Reyee Router app).
2. 2Follow the setup wizard to detect Internet connection type (DHCP or PPPoE).
3. 3Set the administrator password.
4. 4Configure Wi-Fi SSID and password for both 2.4 GHz and 5 GHz bands.
5. 5Enable Reyee Mesh if adding secondary nodes for whole-home coverage.
6. 6Save changes and run speed test in the management console.

Verification Step